Boarding Up Windows And Doors Techniques To Simplify Your Daily Lifethe One Boarding Up Windows And Doors Trick Every Individual Should Be Able To > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

boarding up company near me up windows and doors (metooo.co.uk) Before a Storm Hits

Before a storm hits the windows and doors provides measurable protection from damage. To do this, you should have a few items on hand.

Find the width and height of the window including the frame (not the trim or masonry surrounding the window). Write these measurements down to ensure you don't forget them.

Preparation

It is always recommended to put up a board on doors and windows prior to the storm or another natural disaster hits. This will help prevent damage to property and will minimize the loss of life. It takes an enormous amount of planning to build a board around windows. You will need to purchase and measure plywood boards, and you should be aware of the exact dimensions of each window. It takes time to cut and boarding up windows and doors put in the boards in a proper manner. Fortunately this can be simplified by beginning the preparations when you first hear of a possible storm coming in your area. By doing so you will avoid a stressful last-minute rush and make the process easier for yourself and your employees.

Begin by listening to forecasters for weather and following guidelines issued by your local government. If you start earlier in the process, you will be able to gather the materials and keep them in storage without feeling rushed by a storm that is about to hit. Depending on the severity of the event, you may require massive quantities of plywood to cover your windows. Use a tape to measure the width and height of each window opening. Make sure to include the trim or framing around each window, and any ledges with extended edges if they are necessary.

Divide the total width and height of your window by 2 to determine the size of plywood sheets you'll require. For instance, if the width of your window is 16 inches, the thickness of each sheet should be 8 inches. If your exterior is made of wood drill pilot holes in the plywood sheet to ensure it is aligned with the window frame below. This will reduce splitting when you screw in the screws.

If you have a bigger window than a single sheet of plywood is able to handle, cut two sheets of plywood that are half as large as the desired window. Place them side-by-side on the wall. Cut a 2 by 4 in (5.1 x 10.2 cm) of lumber to the length the connecting edge between the plywood sheets and then place it on top of the seam. Then screw 2.25 in (5.7cm) screws into the plywood sheet and Boarding up windows and doors into the bracing to join the two.

Materials

To ensure security and safety, only use materials that are durable and won't break or shatter in strong winds. Plywood is the most commonly used material for boarding up property up windows. It is simple to use, affordable, and easily available. Pick plywood that is of the exterior grade (CDX), as it is stronger and will have less knots and warps. A more durable alternative is storm shutters, also known as hurricane shutters, which are installed over windows already in use to offer more protection from glass breaking and the weather that can cause a lot of damage.

Once you've identified the position of your windows, measure the width and height of each one to determine how much plywood you will need. Utilize a power drill to make pilot holes into the sheets of plywood around each window at two-inch intervals. Mark the studs on the wall before attaching the plywood to ensure the boards are secured. If your home is constructed with wood siding, search for nailheads that may indicate stud locations. You can also use your drill to locate the locations of studs. Screws should be driven into the framing, not into the trim or sheathing. A plywood panel that is attached only to these materials can become a safety hazard in the event of severe winds.

If the size of your window is too large for a single piece of plywood, cut two separate pieces which are each half the size you require. join them with 2 by 4 inch lumber. Label each sheet of plywood to let you know which window it will cover.

Make sure you use corrosion-resistant screws that are long enough to penetrate the sheathing and the studs to attach the plywood panels to your wall. To secure the plywood panels to the wall, make use of corrosion-resistant screws that are long enough to get through both the sheathing and the studs.

You should also consider installing polycarbonate security glass similar to DefenseLite on your windows that are primary. These transparent shields are bonded to the existing glass to guard your doors and windows. They are virtually unbreakable, deterring criminals from breaking in.

Installation

If you reside or intend to move to an area susceptible to hurricanes and are worried about the possibility of a storm you should consider boarding up service up all your windows and doors. It's a project that can be done quickly and efficiently however only if you make the effort to measure, cut and label your plywood panels before the storm hits.

You'll also need a few other tools, including a drill (or a hammer and nails in the event that you don't have a power drill) and tape, a saw gloves, a level and safety glasses. It's also a good idea for the plywood to be sprayed with sealant to make it waterproof.

Start by measuring the window's height and width. Then cut your plywood sheets to fit into the frames. This is best done on-site because you have more control over the exact dimensions.

Utilize a circular or track saw to cut the boards to the proper size Be aware that you'll need to sand them down after they're installed. Once you've got your boards place, screw 3 inch stainless steel hanger bolts into the framing studs that surround each window. Use washers to secure each bolt as well as wings nuts. Make sure that each screw gets through the studs at least two inches to ensure the board is strong enough to withstand strong winds.

If you're building with concrete blocks, you can attach the plywood to the building using galvanized pan-head screws driven through the edges that overlap of each panel into bricks or cinder blocks. You'll also have to make pilot holes in the masonry and then insert corrosion-resistant screws into the holes. It's a project that can take up to three hours for each window, so it's essential to begin the process immediately after you hear that a hurricane warning has been issued. This will give you plenty of time to finish the project before the storm arrives.

Maintenance

You should be prepared to put up a security barrier on your doors and windows prior to an extreme storm. This will help you to avoid costly repairs and safeguard your home from further damage that could be caused by wind, rain, flying objects and other causes.

The right tools will make the boarding up houses-up process faster and easier to complete. The key is to precisely take measurements of the dimensions of the windows you have to cover. This will ensure that the OSB or plywood fits snugly and won't come off easily. If you're using plywood ensure that you are using exterior-grade sheets and consider adding an extra layer of protection.

After you have the OSB or plywood measured, mark the areas where screws will be inserted into the board. Then, use a drilling machine to pre-drill holes into the plywood at intervals of 12 inches. Then, you can use hanger bolts to secure the boards in an emergency or catastrophe situation. After the storm has passed and you've received the all-clear by local authorities, take off the hanger bolts, but leave them in place for future emergencies.

Then, you can put the plywood panels on top of the windows. Be prepared to work in pairs. If you're using plywood, ensure that you sand the edges so they are smooth and won't scratch your paint or trim. Then use corrosion-resistant screws to attach the plywood using the pilot holes. If your home has shingles made of vinyl it, attach the plywood directly to the shingles and not to the wood framing.

A boarded-up window can also be used to deter burglars. The burglars will be more likely to target a structure with a damaged window or one that is not locked. They're also more likely to enter the store that has been fenced off than one that isn't. This is something that retail business owners should take very seriously.