Fitting a Cat Flap > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Fitting a cat flap can seem intimidating however it's actually quite easy to do by following the correct instructions. Determine how high you would like the flap to be (normally, it is at belly height). Mark this point on your door and use the template included to guide you when drilling.

If you have a small kitten, prop the door open a bit and gradually encourage it to enter. Reward it each time it goes through.

Measure the Door

A cat flap lets your pet to enter and exit your home at any time. This can keep your cat healthy as it will ensure it is exercising regularly and also be able to go back inside when it gets trapped in the elements during bad weather. It can also reduce the amount of time you have to spend letting it out or in and will also help keep your home safe by allowing you to know when it has gone out.

However, it is essential that the flap for your cat flap install is properly fitted to stop your pet from escaping through it or be pushed through by any other animals (e.g. dogs). It is important to measure the height of your pet's stomach and the size of the doorway in your home to ensure that the flap is at the proper height. You can adjust the height of your flap if your cat is taller or smaller than the average.

The next step is to use a spirit level to mark the middle of the door. This is where you will install the flap. Using the marking as a reference, use the jigsaw and cut the form of the flap within the door. After cutting the area, sand down the edges to create smooth surfaces. Make any holes that are required.

The process of installing a cat flap is not as complicated as you believe and it shouldn't take more than two hours for the entire task from start to completion. However, the process may be a little more complicated when you have to install it into the frame of a uPVC or composite door because these doors come in various thicknesses that can affect the way the holes are cut and what they are fixed to. This is why we always recommend calling a professional to complete the work, particularly when you've never dealt with glass before.

Measure Your Cat

You can save yourself hours of listening to the cat Flap step's meows to be let in or out. This is particularly helpful for cats that are inside in all weathers when you are at work.

It is essential to measure your cat first before you attempt the installation. Although it might appear to be an easy task, it is crucial to measure the right way or your cat will find it very difficult to use.

First, make sure that your cat is calm prior to taking measurements. You'll need to keep them in a manner that they cannot move and make sure that the ruler or measuring tape is flat against their body, not bending in any way. You can get an accurate measurement by keeping the measuring tape or ruler flat against the body of the animal from the top to the bottom.

Once you have the measurement of your cat, it's time to look at the door and decide where to place the flap. Position the flap at the level of your cat's belly. This will allow them to walk through the door without much effort. This will also stop the flap from making a lot of noise when it swings back and back.

You will also need to think about the thickness and the structure of the upvc door panel with cat flap fitted door or composite. While all timber doors have a similar thickness to them, upvc cat flap door panels or composite doors may differ in their overall design. This could make the process of the installation of the flap for your cat more difficult since you must ensure that the hole is of the correct size.

It is also worth studying the instructions that come with the cat flap kit to locate an illustration template that can be used to mark the location of the hole in the door. This will help you determine where the opening must be, and also to ensure that the template is properly placed on the door. Using a spirit-level to ensure that the template is right against the door Cat flap step will also prove beneficial.

Cut the Flap

You'll need to make an opening in the door panel to install your cat flap before you can attach it. This is a difficult task and it is recommended to seek the help of an expert cat flap fitter for this step if you don't have the expertise or knowledge to do it yourself. You can also refer to the instructions that come in the kit to find out how to do it properly.

To do this, you have to measure the height of your cat's or kitten's belly and use that as an indication point. As a general rule you should place the flap around 10-15 centimeters higher than the ground. This is the standard height of the stomach for cats. This will let your cat pass through the flap without difficulty and make it more difficult for other cats or naughty neighbors to get in or out.

Mark the position of the cat flap on the door Cat flap step with a pencil. If your kit includes a template, place it over the door. Use the markings on the template to drill holes in each corner. You should then be able to cut the design of the template and replace it with your cat flap.

You can install your cat flap yourself inside the door made of wood or uPVC If you're comfortable using the Jigsaw. Be cautious not to cut into the mullions or rails that run vertically of your door. You can use a jigsaw to cut your panel into a circle or square according to the way you want it. Make sure to take your time and don't try to force the jigsaw to cut faster.

After the hole has been cut then carefully insert the flap onto its new home and make sure that it is securely fixed. If it has screw caps, then push these onto the screws that protrude. Once the screws have been installed, sand the rough edges and seal any gaps. This will prevent the entry of draughts into your home.

Place the Flap

If you have a simple cat flap, you can leave it open and encourage your pet to walk through by putting a small amount of cat food on the outside of the door. You can also push the cat using a stick or your hand. Once your pet has become accustomed to walking through the flap it will be able to come and go at will. This lets you let it in and out at any time it's wanted.

You can install the flap onto an UPVC or glass door however it's not as simple as fitting one into a wood exterior door due to the fact that the UPVC doors and some glass doors don't have a consistent thickness. This could have a significant impact on how you cut the hole for the flap, and can also affect whether your flap is fitted correctly after it has been installed.

The mounting kit might contain a template that outlines the best places to drill holes. If the kit does not include the template you can use a photocopier to create your own. It is important not to use the jigsaw to hard when cutting, so that it doesn't leave a bigger than needed hole in your door.

Most cat flaps are rectangular or square in shape, however there are also some which are circular and these are typically more difficult to fit. If you have a circular flap it is essential to ensure that the hole is in the right position on your door, because if it's not, your cat won't be able to use it and could be stranded out in the sun all day (or even at night).

Some cat flaps have locks that allow you to determine when your cat enters and leaves. They are helpful if your pet is afraid of leaving in the dark or returning in the dark. They are also useful if you work all day. Some locks can be used for either access or exit, and others can be locked in both directions. This is useful for sick or older cats who aren't keen to go outside in bad weather.