Boarding Up Windows And Doors Tools To Ease Your Everyday Lifethe Only Boarding Up Windows And Doors Trick Every Person Should Learn > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Boarding Up Windows and Doors Before a Storm Hits

In the event of a storm, boarding up (kingranks.com) your windows and doors will protect you from damage. To do this, you'll should have a few items on the go.

Find the width and height of the window including the frame (not the trim or the masonry around the window). Note these measurements so you don't forget them.

Preparation

It is recommended to put up a cover your doors and windows prior to an event like a hurricane or natural disaster. This will minimize damage to property and decrease the chance of a fatality. It requires lots of planning to build a board around windows. You have to buy and measure plywood boards, and you should know the specific dimensions of each window. Moreover, it takes time to cut the boards and install them correctly. Fortunately, boarding up the process can be made simpler by preparing when you first hear of a storm that could be coming in your area. You can avoid a stressful rush in the last minute, and make it easier for you and your staff.

Begin by listening to forecasters for weather and follow the guidelines set by your local government. If you start earlier in the process, you will be able to gather the materials and store them without feeling rushed by a storm that is about to hit. Depending on the severity of the imminent event, you may require huge quantities of plywood to cover all of your windows. Make use of a tape to determine the width and height of each window opening. Make sure to consider the trim or framing surrounding each window as well as any extended sills in the event that they are required.

Then, determine the size of the plywood sheets you require by dividing your window's total height and width by 2. If your window is wide of 16 inches, the thickness of each sheet is 8 inches. If you have an exterior made of wood, you should drill pilot holes into the plywood sheet that align with the window frame beneath to avoid splitting when screwing in the screws.

To make sure that the window's opening is larger than what one sheet of plywood can handle, cut two separate sheets that are each half the size of the desired window and lay them side-by-side on the wall. Then cut a piece of 2 by 4 in (5.1 by 10.2 cm) lumber to the length of the connecting edge of the plywood sheets and then place it over the seam. Then then, drive 2.25 in (5.7 cm) screws through the bracing and into the plywood sheet to join them.

Materials

To ensure security and safety, only use materials that are sturdy and will not be damaged or break in high winds. The most common material used to encase windows is plywood, which is affordable, readily available and easy to work with. It's important to choose plywood that is specifically designed for exterior use (CDX) for extra strength and is free of knots and warping. A sturdier alternative is storm shutters or hurricane shutters, which are erected over windows that are already in place to provide more protection against glass shattering and the weather that can cause a lot of damage.

Once you've identified the location of the window openings take measurements of the width and height of each to determine how much plywood you'll need. Utilize a power drill to drill pilot holes into the sheets of plywood around each window at two-inch intervals. Before attaching the plywood, determine and mark the locations of studs on the wall to ensure the boards are fastened securely. If your home is constructed with wood siding, look for nailheads that could indicate stud locations. In other cases, you can search for stud positions with your drill. Screws should be driven into the framing, not into the sheathing or trim. A plywood panel that is attached to these materials alone could cause a safety risk in high winds.

If your window is too big for one sheet of plywood, you could cut two pieces of plywood that are each half the size and join them using two by four inches of lumber. Label each plywood sheet to let you know which window it will cover.

To secure the plywood panels to the wall, use corrosion-resistant screws that are long enough to get through both the sheathing as well as the studs. To attach the plywood panels to the wall, make use of corrosion-resistant screws that are long enough to penetrate the sheathing and the studs.

In addition to securing your windows, you should put up an "No Trespassing" sign on your property boarding up and consider installing polycarbonate security glass such as DefenseLite over your windows. These transparent shields are fixed to the existing glass and safeguard your windows and doors. They are virtually impervious to breakage and discourage burglars from gaining entry into your home.

Installation

If you live in an area susceptible to hurricanes, or plan to move to one the best option is to board up your doors and windows prior to the threat of a storm approaches. This project can be completed quickly and efficiently, however only if the plywood panels are measured, cut, and labeled before the storm arrives.

You'll also require a few other tools, like a drill (or nails and a hammer if you don't have a power drill) as well as tape, a saw an apron, gloves and a pair of safety glasses. It's also a good idea for the plywood to be sprayed with sealant to make it waterproof.

Start by measuring the height and width of each window opening, then cutting your plywood sheets so they fit inside the frames with an overlap of 4 inches on all sides. This is best done on site because you can control the exact dimensions.

Cut the boards to the desired size with a track or circular saw. Once installed it is necessary to sand all of them. Once you've got your boards in place, screw 3-inch stainless steel hanger bolts into the framing studs around each window. Use washers on each bolt and wings nuts to anchor them. Make sure that each screw is inserted at least 2 inches into the studs to ensure the boarding up service near me is strong enough to withstand Boarding Up strong winds.

If you're building with concrete blocks, you can instead join the plywood to the building using galvanized pan-head screws driven through the overlapping edges of each panel into cinder blocks or masonry blocks. It is also necessary to drill pilot holes in the masonry before screwing corrosion-resistant screws into the holes. This task can take up to three hours per time period. It is essential to begin the project as soon as a hurricane warning has been issued. This will allow you enough time to complete your project before the storm hits.

Maintenance

You should be prepared to secure your windows and doors before a severe storm. This will save you money on repairs and also protect your property from further damage resulting from wind, rain, flying debris and other factors that could impact windows.

The right materials can make the boarding up process easier and faster to complete. The key is to precisely determine the dimensions of the windows you'll must cover. This will ensure the OSB or plywood fits well, and that it will not fall off easily. If you're using plywood be sure to use exterior-grade sheets, and consider adding a protective finish.

After you have the OSB or plywood measured, mark the spots where screws will go into the board. Then, use a drill to pre-drill holes into the plywood at 12-inch intervals. This allows you to securely fasten the boards with hanger bolts during a disaster or emergency situation. Once the storm has passed and the local authorities have given you the all-clear, remove the bolts but keep them for future emergencies.

Then, you can put the plywood panels on top of the windows. Be prepared to work in pairs. If you're using wood, make sure you sand the edges so they are smooth and won't scratch your paint or trim. Then make use of corrosion-resistant screws join the plywood with the pilot holes. If your home has shingles made of vinyl it, nail the plywood directly to the shingles, and not to the wood framing.

In addition to keeping out rain and other weather elements, a boarded up window is also a good way to prevent burglary. Burglars are more likely target a building with a broken or unlocked window. They're also more likely to break into a store that's been fenced off than one without. This is something that business owners in retail should consider very seriously.