It's The Ugly Reality About Door Lock Change > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

Change of the door lock is an easy and inexpensive method to increase your home's security. The process is not for all. It requires a certain amount of skill and patience.

The cylinder is contained within the knob body. The cylinder is what recognizes the key when it's put into the lock.

Take off the lock that was previously used.

The first step in replacing the door lock is to remove the old one. It's a fairly simple process, however there are a few points to remember. First, ensure that your new lock is the correct size for your door. This will ensure that it fits properly and does not create a gap around the deadbolt plug or latch.

After you've removed the latch plate look for two screws or bolts on the inside of the casing that secure the casing and halves of the lock. Remove these screws with a screwdriver and then pull the lock from the door. If you have a mortise locking mechanism, there is a set screw that holds the handle to the spindle. Take off the doorknobs by removing this screw using a screwdriver.

Take the deadbolt and latch plug from your door jamb. Then, you can put in your new lock. If you are replacing a mortise lock, you should also measure the distance between the lock case and the edge of your door to ensure that the new lock will be able to fit.

Several reasons might prompt you to replace your door lock, for instance suspecting that someone else has the key or welcoming the arrival of a new roommate. You can save money by deciding to remove the lock yourself instead of hiring an expert. It's much simpler than people think and can be done in just a few moments.

Begin by getting rid of the trim and handle from your door. Then, you can pry the trim loose with a flat screwdriver. You should be able to twist off the majority of it and in certain cases the handles could come off completely. Next, examine the handle for a small pinhole on the inside and insert a straightened paper clip into it. This will activate the release mechanism and allow you to remove the handle from the door. Then, look for a small tab that is located inside of the lock and push it using a flat screwdriver. Once the spindle has been removed, you are able to remove the cylinder and the housing.

Making a choice for a new lock

You have many options when it comes to selecting the right lock. Consider the different types of locks and select one that matches the design of your door. Take into consideration the backset which is the distance between the edge and the center of the hole in the lock. Also, consider the cross bore, a tiny hole that is located at the edge of your door frame. Select a lock that will fit the door thickness and swing.

The majority of door locks have been assessed by BHMA and the American National Standards Institute to provide you with an idea of how well they will withstand use and how difficult to disable or pick. A grade 3 lock could be a good choice for a tranquil suburban apartment complex, whereas a grade 1 lock might hold up better to the traffic near a busy store front on a city street.

Most smart door locks require a digital key code to open. If you are worried about hacking or other security concerns, consult an expert locksmith.

Replace the cylinder

If your door lock cylinder is broken or damaged you can repair replacement upvc window locks double glazed window lock mechanism replacement lock [opensourcebridge.science] it in a matter of minutes using a simple DIY project. The key is to choose the right cylinder, and follow the instructions that are included with it. The first step is to take off the knob or handle in the event that one is present then loosen the trim that is attached to the base of the lock cylinder by using the help of a screwdriver. After the trim has been removed, it is possible to remove the screws holding the cylinder with the flathead. The cylinder is then gently pulled out of the door.

Before you install the new cylinder, be sure that it is the correct length for your door. With an instrument, measure the distance between the cylinder's center and the left and right sides. Buy a new cylinder that has the same measurements. This will stop cylinders from snapping when the door is hit or the key is stuck inside.

Once you have a suitable replacement window locks cylinder, put it in the door and turn the key. This will align the cylinder with the carriage which is located usually on the outside of your lock. Then, loosen the set screws which should be only a couple of turns into the head. If there is a screw at the edge of the case that holds the door, you will need to loosen it.

After removing the lock cylinder after which you can replace it with the new lock by sliding the new cylinder into the case and tightening the set screw. Reinstalling the piece that connects the cylinder to a lock indicator stem is also important. You can do this by pulling three tabs in the back of the cylindrical using needle-nosed pliers. Then, you can attach the second bracket to the back of the cylinder. You must then install the latch plate and strike plate, along with the retaining rings connected to the top of the lock the cylinder.

Installing a new lock

Start by measuring the width of your door if you are replacing a lock that is already in use. The majority of residential locksets come with a thickness of 3/8 inch to 1 3/4 inches. If your door is more than 1 3/8 to 1 3/4 inches, you'll need a thicker door kit. This will include longer screws, or an extension for the spindle or a longer tail piece for door knobs.

The majority of locks come with a detailed instruction manual to assist you in installing the new hardware. Take the time to read the instructions before beginning the process to make sure that you've followed all the steps. The booklet will give you an idea of the amount of skill that is required to complete the task. You might want to ask a friend who has worked with locks for assistance if you are changing locks for the first time.

Before installing the new lock it is an excellent idea to put cover the holes with tape the old hardware. This will stop the screws from falling through the holes, and protect any tiles you may have installed. This will also protect your tiles from any damage caused by dirt, rust and grime. SECURAM Touch comes with a strip painter's tape, which is designed to be used for this purpose, but you can also use gaffer's tape as well as masking tape if you have it available.

After you have removed the screws that hold the interior portion of the lock section to the exterior side, pull it straight away. It's important to do this as quickly as possible so that the lock doesn't end up accidentally closing itself and damaging the mechanism.

If your new lock is equipped with an latch bolt, install the new latch bolt into the upper cross bore. Make sure you put it in the proper position, which will be marked by an arrow. Then, you can screw the latch plate onto the bolt.

Attach the deadbolt to the jamb of the door. Test the deadbolt by throwing it few times to ensure that it is extended all the way to the strike plate and is secure. If you're using an electronic smart lock, make sure to follow the instructions to program it. This involves downloading an application and entering your email address, confirming your identity, then accessing the wireless network to connect your device.